DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. L298n is a kind of high voltage, high current motor driver chip produced by ST company.

Having 15 pins as package, large output currentinstantaneous peak current up to 3A, this chip has such features as high working voltagemaximum voltage up to 46V, continuous working current 2A and 25W of rated power. Two built-in h birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on.

Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal, which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit.

Using l298n chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well. Description:1. Using l298n made by st company as the control chip, the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability.

2.

OSOYOO 10PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot

Gnd: gnd External 3. The ir infrared obstacle avoidance Sensor Module detection range can be through the potentiometer to adjust and have small interference, easy to assemble, easy to use. The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay.

It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, green indicator will light up, when detecting direction meet with obstacles reflecting surface, reflected infrared receiving tube, after the comparator circuit processing, at the same time signal output interface to output digital signal a low level signal.

Can be used for 3-5v dc power supply modules. It has red power indicator. It can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on On-line tutorial: http://osoyoo. Com/2017/07/arduino-lesson-obstacle-avoidance-sensor/ specification the output port out sensor module can be directly connected to the microcontroller IO port, detection angle 35 °, you can directly drive a 5V relay ; the module detects the distance 2 ~ 30cm, the distance can detect potential is adjusted Can be used for 3-5V DC power supply modules When the power is turned on, the red power indicator light Using the comparator LM393 Interface : 1.

Vcc: external 3. 3v-5v voltage can be directly connected to 5v MCU and 3. 3v mcu 2. Out: small board digital output interfaces 0 and 1 connection : VCC-VCC; GND-GND; out-IO With the screw holes of 3mm, easy fixed installation Board Size : 3.


Similar products

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
XLX 50 PCS TCRT5000L TCRT5000 Photoelectric Sensors Reflective Optical Sensor with Transistor Output Infrared 950mm 5V 3A For Tracking and Obstacle Avoidance Car
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
4PCs DC Electric Motor 3-6V Dual Shaft Geared TT Magnetic Gearbox Engine with 4Pcs Plastic Toy Car Tire Wheel, Mini Φ67mm Smart RC Car Robot Tyres Model Gear Parts, Yeeco
Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot XBee ZigBee S03
HiLetgo L293D Motor Driver Shield Compatible to Duemilanove Mega UNO R3 AVR ATMEL


WGCD 10pcs Joystick Breakout Module Game Controller for Arduino PS2

Size:37x25x32mm weight: 15 g connector: +5vcc - gnd - vrx - vry - sw material: abs plastic Game joystick module suits for Arduino PS2, the robot is at your commands with X, connects to two analog inputs, Y control. The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay.

It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, after the comparator circuit processing, when detecting direction meet with obstacles reflecting surface, green indicator will light up, reflected infrared receiving tube, at the same time signal output interface to output digital signal a low level signal.

Can be used for 3-5v dc power supply modules. Package: 10pcs joystick breakout module ir infrared obstacle avoidance sensor Module can be widely used in robot obstacle avoidance, line count, obstacle avoidance car, and black and white line tracking and so on. The module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted.

When pressing at the arrow direction, at opposite direction of the arrow, maximum is 5 v, the voltage value decreases, minimum is 0 v. Package include: 10 pcs XY joystick module. It has red power indicator. Game joystick module for Arduino PS2, electronic building blocks standard connector with 2. 54mm pin.


Similar products

Makerfire 10pcs Arduino NRF24L01+ 2.4GHz Wireless RF Transceiver Module New
Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Teensy LC USB Development Board Without Pins
10 pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Remote Control
DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
HiLetgo® 5pcs Super Mini PAM8403 Digital Power Amplifier Board 2*3W Class D 2.5-5V USB Power
kuman 3 pcs nRF24L01+PA+LNA Antenna Wireless Transceiver RF Transceiver Module for Arduino KY67
Makerfire 4pcs NRF24L01+ Breakout Adapter with on-board 3.3V Regulator for NRF24L01+ Wireless Module
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino


Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino

Microcontroller: atmega2560 operating voltage: 5v input:voltagerecommended :7-9v digital I/O Pins: 54 of which 15 provide PWM output Analog Input Pins: 16 DC Current per I/O Pin: 40 mA DC Current for 3. 3v pin: 50 ma flash memory: 256 kb of which 8 kb used by bootloader sram: 8 kb eeprom: 4 kb clock speed: 16 mhz package includes: 1 x mega 2560 ATmega2560-16AU Board Arduino-compatible 1 x USB cable Ir infrared obstacle avoidance sensor Module can be widely used in robot obstacle avoidance, line count, obstacle avoidance car, and black and white line tracking and so on.

The module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted. We have the manufacture factory, making productions and selling by ourselves. When pressing at the arrow direction, maximum is 5 v, at opposite direction of the arrow, the voltage value decreases, minimum is 0 v.

Package include: 10 pcs XY joystick module. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. Stronger reset circuit. Not designed for high current applications. The mega is 100 percent compatible with Arduino and most shields designed for the Arduino Mega2560 R3.

The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay.


Similar products

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
SunFounder Mega 2560 Case Enclosure Transparent Gloss Acrylic Computer Box Compatible with Arduino Mega 2560 Rev3 R3, Genuino Mega 2560 Rev3 and other Arduino Compatible Mega 
HiLetgo RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board Support Arduino Mega 2560
Elegoo EL-CP-003 3pcs MB-102 Breadboard 830 Point Solderless Prototype PCB Board Kit for Arduino Proto Shield Distribution Connecting Blocks
KINGPRINT Ramps 1.6 Expansion Control Panel with Heatsink Upgraded Ramps 1.4/1.5 for 3D Printer Board
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Electronics-Salon Screw Terminal Block Breakout Module, for Arduino MEGA-2560 R3.
EDGELEC 120pcs Breadboard Jumper Wires 10cm 15cm 20cm 30cm 40cm 50cm 100cm Optional Arduino Wire Dupont Cable Assorted Kit Male to Female Male to Male Female to Female Multicolored Ribbon Cables
WINGONEER Prototype Screw / Terminal Block Shield Board Kit For Arduino MEGA 2560 R3 DIY


Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino

Stronger reset circuit. Not designed for high current applications. The mega is 100 percent compatible with Arduino and most shields designed for the Arduino Mega2560 R3. 100 percent compatible with the official version, for Arduino uno R3. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

New improvement: clearly printed on the female header connector, more precise and easier to use the wire. The chip is atmega2560-16au and Atmega16u2, same with the official version. Features * atmega328p microcontroller * input voltage - 7-12V * 5V Electric current: 500MA * 3. 3v electric current: 50ma * 14 digital i/o pins 6 pwm outputs * 8 analog inputs * 32k Flash Memory * 16Mhz Clock Speed Component listing: 1pcs UNO R3 Development Board 1pcs USB cable.

The uno now uses an atmega16u2 instead of the ATMega8U2 chip. Use 5. 5 * 2. 1mm dc barrel jack compatible with 5. 5 * 2. 5mm dc barrel jack. When pressing at the arrow direction, the voltage value decreases, maximum is 5 v, at opposite direction of the arrow, minimum is 0 v.


Similar products

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
EDGELEC 120pcs Breadboard Jumper Wires 10cm 15cm 20cm 30cm 40cm 50cm 100cm Optional Arduino Wire Dupont Cable Assorted Kit Male to Female Male to Male Female to Female Multicolored Ribbon Cables
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
uxcell 8mm OD 20mm Long Light Load Compression Mould Die Spring Yellow 10pcs
HiLetgo 120pcs/3x40pcs Breadboard Jumper Wires Prototype Board Dupont Wire Male to Male, Male to Female, Female to Female, 2.54mm to 2.54mm 20CM Wires Assortment Kit for Arduino Raspberry PI DIY
SB Uno R3 Case Enclosure New Transparent Clear Computer Box Compatible with Arduino UNO R3
Capricorn Bowden PTFE Tubing XS Series 1 Meter for 1.75mm Filament (Genuine Capricorn Premium Tubing)
9V 1A Arduino Power Supply Adapter 110V AC
LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board for Arduino (Nano x 3 with USB Cable)


Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

We have always cared about the customer experience and improve the product function details. Stronger reset circuit. The uno now uses an atmega16u2 instead of the ATMega8U2 chip. Control using atmel ATMEGA328P chip. Use 5. 5 * 2. 1mm dc barrel jack compatible with 5. 5 * 2. 5mm dc barrel jack. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers.

The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. It has a pair of infrared transmitting and receiving tube, tube infrared emit a certain frequency, after the comparator circuit processing, when detecting direction meet with obstacles reflecting surface, reflected infrared receiving tube, green indicator will light up, at the same time signal output interface to output digital signal a low level signal.

Can be used for 3-5v dc power supply modules. Packing in a color box. We have always cared about the customer experience and improve the product function details. The chip is atmega2560-16au and Atmega16u2, same with the official version. When pressing at the arrow direction, the voltage value decreases, maximum is 5 v, at opposite direction of the arrow, minimum is 0 v.

Package include: 10 pcs XY joystick module.


Similar products

Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
Elegoo EL-CP-003 3pcs MB-102 Breadboard 830 Point Solderless Prototype PCB Board Kit for Arduino Proto Shield Distribution Connecting Blocks
ARDUINO UNO R3 [A000066]
Breadboard Solderless Prototype PCB Board – ALLUS BB-009 (3pcs) 400 Pin with 4 Power Rails and Double Sided Tape for Raspberry Pi and Arduino
9V 1A Arduino Power Supply Adapter 110V AC
Elegoo 17 Values 1% Resistor Kit Assortment, 0 Ohm-1M Ohm (Pack of 525) RoHS Compliant
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino
4PCS Breadboards Kit Include 2PCS 830 Point 2PCS 400 Point Solderless Breadboards for Arduino Proto Shield Distribution Connecting Blocks
ELEGOO 6PCS 170 tie-Points Mini Breadboard kit for Arduino
Arduino Uno R3 Development Board, Kit Microcontroller Based on ATmega328 and ATMEGA16U2 with USB Cable for Arduino, Original


ELEGOO 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

Not designed for high current applications. The mega is 100 percent compatible with Arduino and most shields designed for the Arduino Mega2560 R3. We have always cared about the customer experience and improve the product function details. Control using atmel ATMEGA328P chip. The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay.

It has a pair of infrared transmitting and receiving tube, after the comparator circuit processing, green indicator will light up, when detecting direction meet with obstacles reflecting surface, tube infrared emit a certain frequency, reflected infrared receiving tube, at the same time signal output interface to output digital signal a low level signal.

Can be used for 3-5v dc power supply modules. Use 5. 5 * 2. 1mm dc barrel jack compatible with 5. 5 * 2. 5mm dc barrel jack. So we would like to receive your valuable suggestions for our products and we can improve them for you. 5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board,with convenient use, connect to the 2 phase, direct docking - Rated Voltage: DC5V 4-phase - Insulation Resistance: >10MΩ 500V - Dielectric Strength: 600V AC / 1mA / 1s - Step angle: 5.

625 x 1/64 - dc resistance: 200Ω±7% 25c - reduction ratio: 1/64 - insulation grade: a - no-load Pull in Frequency: >600Hz - No-load Pull out Frequency: >1000Hz - Pull in Torque: >34.


Similar products

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
Elegoo EL-CP-003 3pcs MB-102 Breadboard 830 Point Solderless Prototype PCB Board Kit for Arduino Proto Shield Distribution Connecting Blocks
10 pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Remote Control
E-Projects 10EP5122K20 2.2k Ohm Resistors, 1/2 W, 5% (Pack of 10)
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
ELEGOO Upgraded 37 in 1 Sensor Modules Kit with Tutorial for Arduino UNO R3 MEGA 2560 Nano
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino
Smraza 10 Pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Car Boat Control, Arduino Project
Elegoo EL-KIT-008 Mega 2560 Project The Most Complete Ultimate Starter Kit w/Tutorial for Arduino UNO Nano


4 x TT Motor UniHobby 3-6V Uniaxial DC Gear Motor with Robot Wheels, Motor Support/Bracket for Arduino Robot Smart Car Compatible with Lego

Stepper motor with a standard interface, when used directly pluggable. A, c, b, d four-phase led indicates the status of the stepper motor work.5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board,With convenient use, connect to the 2 phase, direct docking. Drive module board sizein: 1.

37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. 4 robot wheels, motor support/bracket for arduino diy robot car chassis compatible with legodc motor 3-6v single shaft tt gear motor with plastic tire robot wheels, 4 DC Motor UniHobby 3-6V Single Shaft TT Motor with Plastic Tire, Motor Support/Bracket For Arduino DIY Robot Smart Car Chassis Compatible with Lego UniHobby DC Motor Specification: Parameter Operating voltage: 3V-6V DC Recommended Value is 3V Maximum torque: 800g.

Cm 3v speed without load: 125rmp 3v reduction ratio: 1:48 load current: 200mA 500mA MAX 3V pm With EMC, it has strong anti-interference ability and causes no interference to micro-controller. Control using atmel ATMEGA328P chip. Faster transfer rates and more memory. Use 5. 5 * 2. 1mm dc barrel jack compatible with 5.




Similar products

OSOYOO 10PCS IR Infrared Obstacle Avoidance Sensor Module for Arduino Smart Car Robot
4PCs DC Electric Motor 3-6V Dual Shaft Geared TT Magnetic Gearbox Engine with 4Pcs Plastic Toy Car Tire Wheel, Mini Φ67mm Smart RC Car Robot Tyres Model Gear Parts, Yeeco
Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
HC-SR04 Ultrasonic Sensor Distance Module (5pcs) for Arduino UNO MEGA2560 Nano Robot XBee ZigBee by ElecRight
EUDAX 6 Set Rectangular Mini Electric 1.5-3V 24000RPM DC Motor with 84 Pcs Plastic Gears,Electronic Wire, 2 x AA Battery Holder,Boat Rocker Switch,Shaft Propeller for DIY Science Projects
TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects
HiLetgo HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
J-Deal® 10x Pcs SG90 Micro Servo Motor 9G RC Robot Helicopter Airplane Boat Controls
EUDAX 10pcs Micro 130 DC Motor Strong Magnetic Carbon brush DC 3V -12V 25000 RPM Cars Toys Electric Motor, High Speed Torque DIY Remote Control Toy Car Hobby Motor, Metal Car Engine Motor Kit for Toys


ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable

Stronger reset circuit. Dc motor reduction ratio: 1:48 3V Motor No-load speed 125RPM. You could download the driver of Elegoo Nano V3. 0 at: http://bit. Ly/2pmf4in technical specs microcontroller: atmega328 architecture: avr operating voltage: 5 v\ flash memory: 32 kb of which 2 kb used by bootloader sram: 2 kb clock speed: 16 mhz analog i/o pins: 8 eeprom: 1 kb dc current per i/o pins: 40 ma i/o pins input Voltage: 7-12 V Digital I/O Pins: 22 PWM Output: 6 Power Consumption: 19 mA PCB Size: 18 x 45 mm Weight: 7 g Package Include : 3 X Nano Board ATTENTION: We dont have USB cables in this kit and you will need to buy a mini USB cable to use this NANO board.

The nano is a small, complete, and breadboard-friendly board based on the ATmega328 Arduino Nano 3. X. With motor Support compatible with Lego. It's got a pin layout that works well with the Mini or the Basic Stamp TX, GND on one top, RX, ATN, power and ground on the other. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27.

We have always cared about the customer experience and improve the product function details. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board with a little gift. Uniaxial tt Motor with Robot Wheels. You could download the driver of Elegoo Nano V3.


Similar products

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
Makerfire 10pcs Arduino NRF24L01+ 2.4GHz Wireless RF Transceiver Module New
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
Elegoo EL-CB-003 MEGA 2560 R3 Board ATmega2560 ATMEGA16U2 + USB Cable for Arduino
ELEGOO 32 Pcs Double Sided PCB Board Prototype Kit for DIY Soldering with 5 Sizes Compatible with Arduino Kits
HiLetgo HC-05 6 Pin Wireless Bluetooth RF Transceiver Module Serial BT Module for Arduino
MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module Blue I2C OLED Screen Driver DC 3.3V~5V for Arduino
AUSTOR 100 Pcs PCB Board Kit Including 30 Pcs Double Sided Prototype Boards and 30 Pcs 40 Pin 2.54mm Male and Female Header Connector(Bonus: 10 Pcs 2P&3P Screw Terminal Blocks and 30 Pcs Jumper Caps)
Elegoo EL-CP-003 3pcs MB-102 Breadboard 830 Point Solderless Prototype PCB Board Kit for Arduino Proto Shield Distribution Connecting Blocks
MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module White I2C OLED Screen Driver DC 3.3V~5V for Arduino


Makerfire 10pcs Arduino NRF24L01+ 2.4GHz Wireless RF Transceiver Module New

We will do our best to give you a satisfactory answer. Uniaxial tt Motor with Robot Wheels. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls.

Built-in power Down and Standby modes makes power saving easily realizable. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, so users have more breadboard space.

Current consumption is very low, only 9. 0ma at an output power of -6dBm and 12. 3ma in RX mode. Built-in 2. 4ghz antenna. When pressing at the arrow direction, at opposite direction of the arrow, maximum is 5 v, the voltage value decreases, minimum is 0 v. Package include: 10 pcs XY joystick module. Parameter operating voltage: 3V-6V DC TT Motor.

.


Similar products

kuman 3 pcs nRF24L01+PA+LNA Antenna Wireless Transceiver RF Transceiver Module for Arduino KY67
ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
Makerfocus 5pcs nRF24L01+ and ESP8266 ESP-01 Breadboard Breakout Adapter Board Common to Both
LAFVIN Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board for Arduino (Nano x 3 with USB Cable)
Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
Longruner Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module for Arduino (10Pcs)
MakerFocus 4pcs ESP8266 ESP-01 Serial Wireless WiFi Transceiver Receiver Module 1MB SPI Flash DC3.0-3.6V Internet of Things WiFi Module Board Compatible with Arduino
Longruner 3pcs Wireless Transceiver Module 2.4G 1100m NRF24L01+PA+LNA in Antistatic Foam for Arduino Compatible with Antenna LKY67
Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino
WGCD 10pcs Joystick Breakout Module Game Controller for Arduino PS2


10 pcs SG90 9G Micro Servo Motor Kit for RC Robot Arm Helicopter Airplane Remote Control

Please note: the starting current of the motor should be over than 1A and they are analog servos need to continuously provide PMW signal, then it will be work normally. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls. Including 1x 40-pin male to female jumper wires, 1X 40-pin male to male jumper wires, 1x40-pin female to female jumper wires.

With motor Support compatible with Lego. The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. Not designed for high current applications. The mega is 100 percent compatible with Arduino and most shields designed for the Arduino Mega2560 R3.

Interface type: compatible with jr & futaba interface. Motor working Time: 10000 Hours. Miuzei sg90 9g micro servo motor kit for rc robot arm helicopter airplane remote control product specificationmode number:ms18 control specification:control system:change the pulse widthamplifier type:analog controlleroperating trave:l120°±10° 900→2100 μsecLeft&Right travelling Angle deviation:≤ 6°Centering deviation:≤ 1°Neutral position:1500 μsecDead band width:7 μsecRotating direction:Counter Clockwise 900→2100μsecPulse width range:900→2100 μsecMaximum travel:About 120° 900→2100 μsecApply Environmental Condition:Operating Temperature Range:-10℃~50℃Operating Voltage Range:4.

8v~6. 0v electrical specification Function of the Performance:Operating speed at no load 009±0


Similar products

Φ1.2mm x L180mm (7.1 inch) Steel Z PULL / PUSH Rods Parts for RC Airplane Plane Boat Replacement (Pack of 10)
Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino
30A RC Brushless Motor Electric Speed Controller ESC 3A UBEC with XT60 & 3.5mm bullet plugs
Hobbypark 10 Sets Nylon Standard Control Horns W13xL18xH25mm 4 Holes with Screw for RC Airplane Parts KT Model Replacement
ELEGOO 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino
Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi(Pack of 3pcs)
Seamuing 4Pcs MG995 Analog Servo Metal Gear Servo 20KG High Speed Torque Digital Servo Motor for Smart Car Robot Boat RC Helicopter(Control Angle 180)
HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
LewanSoul 6 Channel Digital Servo Tester Over-Current Protection
Hobbypark 25pcs Adjustable Pushrod Connector Linkage Stoppers D1.3mm RC Airplane Plane Parts

CHOETECH USB-C PD Charger, 5-Port 60W Wall Charger with 30W Power Delivery and 18W Quick Charge 3.0 Compatible with MacBook, iPad Pro, MacBook Air iPhone Xs Max Xr X 8, iPad, Samsung Galaxy, and More

LINESO 2 Pack SATA 15 Pin Male to 4xSATA 15 Pin Female Power Splitter Cables L=19.5Inches 50CM